|
Standardization
|
SY/T5037-2000
|
GB/T9711.1-1997(A Grade)
|
API Spec 5L(A Grade)
|
Applicable scope
|
The fuel gas, water, the coal gas, air, heating, vapor and other ordinary fluid conduit uses steel pipe
|
The petroleum＆gas industry transport uses steel pipe
|
The petroleum＆gas industry transportation uses steel pipe
|
|
Type
|
Q195、Q215、Q235
|
L175——L483
|
A、B、X42～X70
|
|
Size
|
Body
Out
Diameter
|
D＜508 ±0.75%D
D≥508 ±1.00%D
|
D＜508 ±0.75%D
D≥508 ±1.00%D
|
D＜508 ±0.75%D
508≤D≤914 -0.25%D～+0.75%D
D＞914 -3.20～+6.35
|
|
Jet
Out
Diameter
|
D＜508 ±0.75%D or ±2.5 (Minimum)
D≥508 +0.50%D or ±4.5 (Minimum)
|
D≤273.1 -0.40～+1.59
D＞323.9 -0.79～+2.38
|
D≤273.1... -0.40～+1.59
D＞273.1... -0.79～+2.38
|
|
Deviation
|
Wall Thickness
|
<508
|
±12.5%t
|
-12.5%t～+15.0%t
|
-12.5%t～+15.0%t
|
|
≥508
|
±10.0%t
|
L175～L245 -10.0%t～+17.5%t
|
≤B Grade -12.5%t～+17.5%t
|
|
L290～L555 -8.0%t～+19.5%t
|
≥X42 -8.0%t ～+19.5%t
|
|
Ellipticity
|
Within 100mm of Jet Out ±1%D
|
Within the Jet scope of 101.6 which its D＞508,the maximum OD≤1%D of the gauge and the minimum OD≥1%D of the gauge
|
Within the Jet scope of 101.6 which its D＞
508,the maximum OD≤1%D of the gauge and the minimum OD≥1%D of the gauge
|
|
Bending
|
≤0.2% of the total length
|
≤0.2% of the total
length
|
≤0.2% of the total
length
|
|
Jet bevel
|
Bevel angle 30°--35°
Shoulder 1.6±0.8
|
Bevel angle 30°--35°
Shoulder 1.59±0.79
|
Bevel angle 30°--35°
Shoulder 1.59±0.79
|
|
Cuts slanting
|
D＜813 , ≤1.6
D≥813 , ≤3.0
|
＜1.59
|
＜1.59
|
|
Inlaying
|
t≤12.7
|
0.35t and ≤3.0
|
≤1.59
|
≤1.59
|
|
t＞12.7
|
0.25t
|
Minimum between 0.1251 and 3.18
|
Minimum between 0.1251 and 3.18
|
|
Welded joint surplus height
|
T≤13…＜3.2
t＞13 ＜4.8
|
T≤12.7…＜3.18
t＞12.7 ＜4.76
|
T≤12.7…＜3.18
t＞12.7 ＜4.76
|
|
Chemical analysis
|
Select a sample from each batch
|
Select two samples from each batch
|
Select two samples from each batch
|
|
Stretch testing sample
|
Select a welded joint from each testing lots
|
Material: Select a sample from each batch
Spiral welded joint: Select a sample from each batch
Butt-welded joint: select a sample within 50
|
Material: Select a sample from each batch
Spiral welded joint: Select a sample from each testing lots Butt-welded joint: select a sample within 50
|
|
Oriented bend testing
|
Not available
|
Select a front-side bending sample and a reverse-side bending sample from each testing lots
Select a front-side bending sample and a reverse-side bending sample within 50 Butt-welded joints
|
Select a front-side bending sample and a reverse-side bending sample from each testing lots
Select a front-side bending sample and a reverse -side bending sample within 50 Butt-welded joints
|
|
Break toughness testing
|
Not available
|
Per the contracts, select
3 charpy impacts from each batch
When D≥508, select 2 drop hammer impacts from each batch
|
Per the contracts, select
3 charpy impacts from each batch
When D≥508, select 2 drop hammer impacts from each batch
|
|
NDT
|
Implement UT or XT to the Repair welded joint, Butt-welded join and surround welded joint; inspect 20% of the spiral welded joint of the pipes; inspect 100% of the spiral welded seam which are the pipes used for flammable gas transportation
|
Implement 100% UT or XT; implement XT to the butt-welded joint ,T- welded joint and 203mm of the jet
|
Implement 100% UT or XT; implement XT to the butt-welded joint ,T-welded joint and 203mm of the jet
|
|
D: Steel Pipe Average External Diameter ,mm T: Steel pipe normal wall thickness ,mm
[σ]: Hydrostatic pressure test stress, MPa
L: Length of single steel pipe P: Hydrostatic pressure test stress, MPa
|
